Victron Energy Inverter / Chargers

PHOENIX MULTIPLUS

Inversor-cargador-Victron-Energy-Phoenix-Multiplus-1.jpg

Multi-functional, with intelligent power management

The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology, and a high-speed AC transfer switch in a single compact enclosure. Next to these primary functions,
the MultiPlus has several advanced features, as outlined below.

Two AC Outputs

The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.

The second output is live only when AC is available on one of the inputs of the MultiPlus. Loads that should not discharge the battery, like a water heater for example, can be connected to this output (second output available on models rated at 3kVA and more).

Virtually unlimited power thanks to parallel operation

Up to 6 Multi's can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will provide 25 kW / 30 kVA output power with 720 Amps charging capacity.

Three phase capability

In addition to parallel connection, three units of the same model can be configured for three-phase output. But that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more than 2000 Amps charging capacity.

PowerControl - Dealing with limited generator, shore side or grid power

The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (nearly 10A per 5kVA Multi at 230
VAC). With the Multi Control Panel a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded.

PowerAssist - Boosting the capacity of shore or generator power

This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement the capacity of the alternative source. Where peak power is so often required only for a limited period, the MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power from the battery. When the load reduces, the spare power is used to recharge the battery.

Four stage adaptive charger and dual bank battery charging

The main output provides a powerful charge to the battery system by means of advanced ‘adaptive charge’ software. The software fine-tunes the three stage automatic process to suit the condition of the battery, and adds a fourth stage for long periods of float charging. The adaptive charge process is described in more detail on the Phoenix Charger datasheet and on our website, under Technical Information. In addition to this, the MultiPlus will charge a second battery using an independent trickle charge output intended for a main engine or generator starter battery (trickle charge output available on 12V and 24V models only).

System configuring has never been easier

After installation, the MultiPlus is ready to go. If settings have to be changed, this can be done in amatter of minutes with a new DIP switch setting procedure.

Even parallel and 3-phase operation can be programmed with DIP switches: no computer needed!

Alternatively, VE.Net can be used instead of the DIPswitches.

And sophisticated software (VE.Bus Quick Configure and VE.Bus System Configurator) is available to configure several new, advanced, features.

 

C 12 / 800 / 35

C 24 / 800 / 35

C 12 / 1200 / 50

C 24 / 1200 / 24

C 12 / 1600 / 70

C 12 / 1600 / 40

C 12 / 2000 / 80

C 12 / 2000 / 50

12 / 3000 / 120

24 / 3000 / 70
48 / 3000 / 35

 

24 / 5000 / 120

48 / 5000 / 120

Electrical specifications            
PowerControl Yes Yes Yes Yes Yes Yes
PowerAssist Yes Yes Yes Yes Yes Yes
Transfer switch 16 Amp 16 Amp 16 Amp 30 Amp 16 or 50 Amp 50 or 100 Amp
Parallel and 3-phase operation Yes Yes Yes Yes Yes Yes
Inverter            
Output power (continuous) 800 VA 1200 VA 1600 VA 2000 VA 3000 VA 5000 VA

Output power 25 ºC

700 W 1000 W 1300 W 1600 W 2500 W 4000 W
Output Power 40 ºC 650 W 900 W 1200 W 1400 W 2200 W 4000 W
Peak power 1600 W 2400 W 3000 W 4000 W 6000 W 10000 W
Output voltage 230 Vac ±2%
Output Frequancy 50 Hz ±0,1 Hz
Wave Signal True Sine Wave
Maximum efficiency 92 / 94 % 93 / 94 % 93 / 94 % 93 / 94 % 93 / 94 / 95 % 94 / 95 %
Zero load power 8 / 10 W 8 / 10 W 8 / 10 W 9 / 11 W 20 / 20 / 25 W 30 / 35 W
Zero load power (AES mode) 5 / 8 W 5 / 8 W 5 / 8 W 7 / 9 W 15 / 15 / 20 W 20 / 20 W
Search mode load 2 / 3 W 2 / 3 W 2 / 3 W 3 / 4 W 8 / 10 / 12 W 10 / 15 W
Charger            
Input voltage 187 - 265 Vac, 45 - 65 Hz, Power factor 1
Charge current 35 / 16 Amp 50 / 25 Amp 70 / 40 Amp 80 / 50 Amp 120 / 70 / 35 Amp 120 / 70 Amp
Auxiliar Battery charge current 4 Amp (12 and 24 volts only)
Absroption charge voltage 14,4 / 28,8 / 57,6 Vcc
Float charge voltage 13,8 / 27,6 / 55,2 Vcc
Storage mode voltage 13,2 / 26,4 / 52,8 Vcc
Battery temperature sensor Included
General            
Programmable relay Yes
Protections

output short circuit, overload, battery voltage too high, battery voltage

too low, temperature too high, 230 VAC on inverter output, input voltage ripple too high

Operating temperature range -40 to 50 ºC
Mechanical specifications
Material and colour Aluminium, Blue RAL 3012
Device mounting Wall mount (backplate included).
Battery connections Cables of 1,5 mts. M8 bolts 4 x M8 bolts
Battery connections G-ST18i connectors Spring-clamp Screw terminals 13 mm2 M6 Bolts
Inverter Dimensions (mm) 375 x 241 x 110 525 x 255 x 125 362 x 258 x 218 444 x 328 x 240
Weight 10 Kgr 10 Kgr 10 Kgr 12 Kgr 18 Kgr 30 Kgr
Environmental specifications            
IP Degree of protection IP 21 (sensitive electric componentes sealed inside enclosure)
Operating temperature range - 40 to 50 ºC
Warranty 5 years
Standards  
Safety EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1, EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1
Emission, Immunity

EN 55014-1, EN 55014-2, EN-IEC 61000-3-2, EN-IEC 61000-3-3, IEC 61000-6-1, IEC 61000-6-2, IEC 61000-6-3

Automotive

12V and 24V models: ECE R10-4

 

Catálogo General 2020

  • Inversor-cargador-Victron-Energy-Phoenix-Multiplus-1.jpg
  • Inversor-cargador-Victron-Energy-Phoenix-Multiplus-12/2000.jpg

Do you want more information about this product?

bornay@bornay.com  |  (+34) 965 560 025  |  Skype